Drilling Speed and Feed Calculator (RPM, Feed Rate & Cutting Speed)

Workshop calculator

    Drilling Speed and Feed Calculator

    Find a starting spindle speed (RPM) and drilling feed rate from your drill diameter, cutting speed, and feed per revolution. Switch between metric and imperial units, then compare the result with your machine’s limits and the drill manufacturer’s guidance.

    Calculate drilling RPM and feed

    Change any value to match your setup.
    Preset speed is only a starting point; actual values vary by alloy, drill, rigidity, and operation.
    Selecting a material or drill type fills an editable cutting-speed estimate.
    Use the cutting diameter of the drill.
    Use the tool maker’s recommended surface speed when available.
    The drill advances this distance during one spindle revolution.
    If set, feed is recalculated using the capped spindle speed.
    Results update automatically when inputs change.
    Recommended spindle speed—revolutions per minute
    Linear feed rate—mm/min
    Feed per revolution—mm/rev
    Enter valid positive values to calculate a starting point.

    How to calculate drill speed and feed

    A drilling speed and feed calculation connects three practical settings: cutting speed at the drill’s outer edge, spindle speed in revolutions per minute (RPM), and how quickly the drill advances into the material. The drill diameter matters because a larger drill travels farther at its cutting edge during each revolution, so it needs fewer RPM to maintain the same cutting speed.

    Formulas used by this calculator

    Metric spindle speed: RPM = (1000 × cutting speed in m/min) ÷ (Ï€ × drill diameter in mm)
    Metric feed rate: mm/min = RPM × feed per revolution in mm/rev
    Imperial spindle speed: RPM = (12 × cutting speed in ft/min) ÷ (Ï€ × drill diameter in inches)
    Imperial feed rate: in/min = RPM × feed per revolution in in/rev

    The calculator keeps your chosen feed per revolution constant when it applies an optional RPM cap, then recalculates the linear feed rate from the capped RPM. This makes the displayed feed rate consistent with the spindle speed your machine can actually run.

    How to use the drilling calculator

    • Select metric or imperial units before entering dimensions and cutting speed.
    • Choose a material and drill baseline to load an editable speed estimate, or select custom and enter a value from your tooling data.
    • Enter drill diameter and feed per revolution. Use the drill maker’s feed chart where one is available.
    • Enter your machine’s maximum RPM if you want the calculator to cap the result.
    • Use the displayed RPM and feed rate as a starting point, then account for setup rigidity, hole depth, coolant, chip evacuation, and the machine’s available settings.

    Choosing a safe starting point

    There is no single cutting speed or feed that suits every drill and workpiece. High-speed steel (HSS), cobalt, and carbide drills can have very different recommendations. Alloy, hardness, coating, hole depth, coolant, machine rigidity, and whether the hole is interrupted all affect the result. The presets are broad educational estimates, not a substitute for a manufacturer’s application data.

    Drilling Speed and Feed Calculator formula


    For deep holes, chips may need to be cleared with a peck cycle, and the best feed can differ from a shallow-hole recommendation. A setup that chatters, squeals, heats rapidly, or produces poor chips may need adjustment. Follow shop procedures, secure the workpiece, and keep hands clear of rotating tooling.

    Frequently asked questions

    What is the difference between drilling RPM and feed rate?

    RPM describes how quickly the drill rotates. Feed rate describes how quickly it travels into the workpiece, usually in mm/min or inches/min. Feed rate is RPM multiplied by feed per revolution.

    Why does a larger drill need a lower RPM?

    At the same RPM, the cutting edge of a larger drill moves faster around the outside diameter. Reducing spindle speed helps keep the edge near the chosen cutting speed.

    Are the material presets exact recommendations?

    No. They are editable starting estimates for general planning. Check the drill manufacturer’s cutting-speed and feed data for your exact material, drill geometry, coating, coolant, and hole conditions.

    What does the maximum RPM field do?

    When the calculated RPM exceeds the limit, the calculator uses the maximum RPM and recalculates the linear feed rate while preserving the entered feed per revolution.

    Can I use this for wood or plastic?

    The formulas work for calculating rotational and linear rates, but material behavior and safe tooling speeds vary widely. Use a manufacturer or machine-maker recommendation appropriate to your tool and material.

    Use as a planning aid: Always verify speeds and feeds with the drill manufacturer and machine documentation. This calculator cannot account for every material condition, tool geometry, machine limit, workholding setup, or safety requirement.
    Tags

    Post a Comment

    0 Comments
    * Please Don't Spam Here. All the Comments are Reviewed by Admin.