Boiler Feed Pump Calculator - Online For Free

Boiler Feed Pump Calculator

Estimate the boiler feedwater flow, required pump head, and pump input power from your steam rate and system conditions. Enter consistent operating values below; results update when you calculate.

Operating data

Tonnes of steam produced per hour.
Added to steam rate to estimate feedwater demand.
Optional capacity margin applied to calculated feed flow.
Enter gauge pressure; atmospheric pressure is added internally.
Use negative values for vacuum conditions.
Vertical difference from pump centerline to boiler feed connection.
Include discharge-side friction and equipment losses.
Use density near actual pump operating temperature.
Efficiency at the expected operating point.

Estimated results

Required feedwater flow (including margin)—
Estimated total dynamic head—
Hydraulic power to the water—
Estimated pump input power—

    How to size a boiler feed pump

    A boiler feed pump moves treated water from the feed tank or deaerator into a pressurized boiler. Its duty point is usually described by flow and total dynamic head (TDH). Flow must cover steam leaving the boiler and water lost through blowdown; head must overcome boiler pressure, elevation, suction pressure, and piping or equipment losses.

    This boiler feed pump calculator provides a preliminary estimate using your steam production rate. The flow allowance is calculated as steam rate multiplied by one plus the blowdown fraction, then multiplied by the optional sizing margin. For example, a 10 t/h steam rate with 3% blowdown and 10% margin gives an estimated feed flow of 11.33 t/h. Dividing by feedwater density converts mass flow to volumetric flow.

    Calculation method

    Feed mass flow = Steam production × (1 + blowdown % / 100) × (1 + flow margin % / 100)
    Pressure head = (boiler pressure − suction pressure) × 100,000 / (feedwater density × 9.80665)
    TDH = pressure head + discharge elevation + estimated system losses
    Hydraulic power = density × 9.80665 × flow (m³/s) × TDH / 1,000
    Pump input power = hydraulic power / pump efficiency fraction

    Gauge pressure differences can be used directly because atmospheric pressure cancels when both pressure values use the same reference. The calculation assumes the stated losses represent the full relevant system loss and treats the entered efficiency as pump efficiency. It does not select a pump or motor, predict performance away from the stated duty point, or calculate NPSH.


    Other post:-https://www.instantinsolution.com/2026/10/georgia-intangible-tax-calculator.html

    What to check before selecting a pump

    • Confirm whether blowdown is expressed as a percentage of steam production or as a separate measured flow. This calculator uses a percentage of steam rate.
    • Estimate friction losses at the intended flow, including the deaerator outlet, feed line, control valve, check valve, economizer, and fittings as applicable.
    • Use water density at the actual suction temperature. Hot feedwater has lower density and can have limited NPSH margin.
    • Check the manufacturer curve for flow, head, efficiency, minimum continuous stable flow, allowable operating region, materials, temperature rating, and NPSH required.
    • Have a qualified boiler or rotating-equipment engineer confirm operating, startup, standby, and code requirements before procurement.
    Engineering note: This online estimate is for preliminary planning and education. Boiler pressure, feedwater temperature, control-valve pressure drop, deaerator conditions, transient demand, and applicable codes can materially change the selected pump duty. Do not use the result as the sole basis for equipment purchase or safety decisions.

    Frequently asked questions

    What flow rate should a boiler feed pump deliver?
    At minimum, it must replace steam production and blowdown at the boiler operating condition. Actual selection may require additional capacity for load changes, startup, redundancy, or the boiler manufacturer's specified margin.

    How is boiler feed pump head estimated?
    Convert the pressure difference between the boiler connection and pump suction into metres of feedwater head, then add elevation and system losses. Confirm the pressure reference and evaluate the entire system.

    Why does hot feedwater matter?
    Temperature affects water density, vapor pressure, and available NPSH. A flow and head estimate alone cannot establish that cavitation will be avoided; compare available NPSH with the selected pump's required NPSH.

    Tags

    Post a Comment

    0 Comments
    * Please Don't Spam Here. All the Comments are Reviewed by Admin.